1.     Don't be a dotard!
    Read these "rules" AND introduce
    yourself     before your first post
  2. A healthy approach to understanding measurements
    Being true to what the artists intended
  3. After being asked for the 308th time, Merv lists top 5 headphones
    (opinion / entertainment piece)
    Dismiss Notice
  4. $1000 to the first to design a headamp using discrete components with better measurements than Magni 3+
    Dismiss Notice
IMPORTANT: New Members Read This Don't Be a Measurement Fascist Merv's Top 5 Headphones - 2023 Edition $1000 Challenge

diy

Page 4 of 4
  1. aufmerksam
    Thread

    Cheap Speaker Stand

    So I figured I would contribute something potentially helpful. I recently (finally) got a pair of black lsr305s for less than the going rate. My...
    Thread by: aufmerksam, Nov 5, 2015, 8 replies, in forum: DIY
  2. FlySweep
    Thread

    ECP Torpedo III [indexed in first post]

    It's here! The highly anticipated (at least by me and many others!) ECP Torpedo III. For those unaware, these links should get you initiated:...
    Thread by: FlySweep, Nov 2, 2015, 1,578 replies, in forum: Headphone Amplifiers and Combo (DAC/Amp) Units
  3. batriq
    Thread

    Composite Capcitors

    I was trying to make a composite cap from two e.g. 350V 150uF caps in series and I needed balancing resistors. I found some information online...
    Thread by: batriq, Nov 1, 2015, 0 replies, in forum: DIY
  4. Cspirou
    Thread

    I need a project for this transformer

    I have a 50 VA R-Core transformer with 2x24vac secondaries. I need some ideas for a project I can use it with. 24 VAC is usually used with speaker...
    Thread by: Cspirou, Oct 27, 2015, 5 replies, in forum: DIY
  5. Cspirou
    Thread

    Using Luhndahl for Parafeed

    First here is the datasheet for a Luhndahl transformer. http://www.lundahl.se/wp-content/uploads/datasheets/1620_3_7_9202.pdf If I am reading...
    Thread by: Cspirou, Oct 24, 2015, 4 replies, in forum: DIY
  6. OJneg
    Thread

    Ideas for a kick-ass 8" monitor

    Tweeter: [IMG] Vifa XT25 ring radiator. Looks like great extension on the top-end and it can be crossed reasonably low. Not nearly as pricy as...
    Thread by: OJneg, Oct 22, 2015, 37 replies, in forum: Speakers
  7. Cspirou
    Thread

    The best power supply

    As far as most things in the world of audio go, there is no real "best". I think power supplies though are an exception where there really is such...
    Thread by: Cspirou, Oct 17, 2015, 11 replies, in forum: DIY
  8. Cspirou
    Thread

    ALPS RK50

    So while looking at potentiometers I found out about the Alps RK50...
    Thread by: Cspirou, Oct 15, 2015, 4 replies, in forum: DIY
  9. ultrabike
    Thread

    The Empiric by Felib

    These are DIY sweet cheeks of wood that Felib put together using drivers from somewheres in the interwebz. Let's start by going through the...
    Thread by: ultrabike, Oct 14, 2015, 11 replies, in forum: Headphone Measurements
  10. TMoney
    Thread

    Bottlehead Audio Thread

    We could use a thread on all things Bottlehead Audio for everyone to share their stories and experiences with Bottlehead Gear. -- I purchased a...
    Thread by: TMoney, Oct 13, 2015, 5 replies, in forum: DIY
  11. sorrodje
    Thread

    The Daphile Thread

    Who's using Daphile here ? Share your experiences : [IMG] http://www.daphile.com/ https://www.facebook.com/Daphile?fref=ts - Gentoo Linux...
    Thread by: sorrodje, Oct 13, 2015, 56 replies, in forum: Computer Audiophile: Software, Configs, Tools
  12. Cspirou
    Thread

    LJM HA-PRO Amp

    My collection has a bunch of high impedance headphones including the Koss MV1(250 ohms), Sennheiser HD250 Linear I (600 ohm) and the recently...
    Thread by: Cspirou, Oct 7, 2015, 2 replies, in forum: DIY
  13. Cspirou
    Thread

    Electronic Schematic Software with tubes

    Does anyone in the community know good software for schematics with vacuum tubes? I found TubeCad but I was wondering if there are other options...
    Thread by: Cspirou, Oct 3, 2015, 3 replies, in forum: DIY
  14. Skyline
    Thread

    Cable Building

    Hey all... I'd like to look into making some cables. Does anyone have a good pictorial tutorial that they can point me towards?
    Thread by: Skyline, Sep 30, 2015, 1,131 replies, in forum: DIY
Showing results 61 to 74 of 74
Page 4 of 4